Pemantauan dan Pengendalian Suhu On/Off Via IoT dengan Kit iTCLab Menggunakan Pengaturan PWM

Perangkat yang diperlukan:

Aplikasi : IoT MQTT Panel di HP Android
Cloud IoT sebagai Broker MQTT : hivemq.com
Device : Menggunakan Kit iTCLab

Berikut ini contoh program yang harus diupload ke Kit iTCLab:

/*******************************************
 * Program : Kendali Suhu On/Off via IoT
 *           Menggunakan Kit iTCLab, dengan
 *           Memperhatikan Pengaturan PWM
 * Oleh    : Tim io-t.net
 * Surabaya, 18 April 2022
 *******************************************/

#include <WiFi.h>
#include <PubSubClient.h>
#include <Arduino.h>

const char* ssid = "wifi"; // Enter your WiFi name
const char* password =  "Password_Wifi"; // Enter WiFi password

#define mqttServer "broker.hivemq.com"
#define mqttPort 1883

WiFiServer server(80);
WiFiClient espClient;
PubSubClient client(espClient);

String Topic;
String Payload;

// constants
const int baud = 115200;       // serial baud rate

// pin numbers corresponding to signals on the iTCLab Shield
const int pinT1   = 34;         // T1
const int pinT2   = 35;         // T2
const int pinQ1   = 32;         // Q1
const int pinQ2   = 33;         // Q2
const int pinLED  = 26;         // LED

// setting PWM properties
const int freq = 5000; //5000
const int ledChannel = 0;
const int Q1Channel = 1;
const int Q2Channel = 2;
const int resolutionLedChannel = 8; //Resolution 8, 10, 12, 15
const int resolutionQ1Channel = 8; //Resolution 8, 10, 12, 15
const int resolutionQ2Channel = 8; //Resolution 8, 10, 12, 15

float cel, cel1, degC, degC1;
const float batas_suhu_atas = 58;

// global variables
float Q1 = 0;                 // value written to Q1 pin
float Q2 = 0;                 // value written to Q2 pin
int iwrite_value = 25;          // integer value for writing
int iwrite_min = 0;            // integer value for writing

void setup() {
  // put your setup code here, to run once:

  Serial.begin(baud); 
  while (!Serial) {
    ; // wait for serial port to connect.
  }

  // configure pinQ1 PWM functionalitites
  ledcSetup(Q1Channel, freq, resolutionQ1Channel);
  
  // attach the channel to the pinQ1 to be controlled
  ledcAttachPin(pinQ1, Q1Channel); 

  // configure pinQ2 PWM functionalitites
  ledcSetup(Q2Channel, freq, resolutionQ2Channel);
  
  // attach the channel to the pinQ2 to be controlled
  ledcAttachPin(pinQ2, Q2Channel);   

  // configure pinLED PWM functionalitites
  ledcSetup(ledChannel, freq, resolutionLedChannel);
  
  // attach the channel to the pinLED to be controlled
  ledcAttachPin(pinLED, ledChannel); 

  ledcWrite(Q1Channel,0);
  ledcWrite(Q2Channel,0); 
  ledcWrite(ledChannel,0); 
 
  // Connect to WiFi network
  Serial.println();
  Serial.println();
  Serial.print("Connecting to ");
  Serial.println(ssid); 
  WiFi.begin(ssid, password);
 
  while (WiFi.status() != WL_CONNECTED) {
    delay(500);
    Serial.print(".");
  }
  Serial.println("");
  Serial.println("WiFi connected");
 
  // Connect to Server IoT (CloudMQTT)
  client.setServer(mqttServer, mqttPort);
  client.setCallback(receivedCallback);
 
  while (!client.connected()) {
    Serial.println("Connecting to CLoud IoT ...");
 
//    if (client.connect("ESP32Client", mqttUser, mqttPassword )) {
     if (client.connect("iTCLab Suhu On/Off")) { 

      Serial.println("connected");
      Serial.print("Message received: ");
   
    } else {
      Serial.print("failed with state ");
      Serial.print(client.state());
      delay(2000);
    }
    client.subscribe("heater1");
    client.subscribe("heater2");
  }
}

void Q1on(){
    ledcWrite(Q1Channel,iwrite_value);
    //Q1 = iwrite_value/255*100;
    //Serial.println(Q1);
}

void Q1off(){
    ledcWrite(Q1Channel,iwrite_min);
    //Q1 = iwrite_min/255*100;
    //Serial.println(Q1);
}

void Q2on(){
    ledcWrite(Q2Channel,iwrite_value);
    //Q2 = iwrite_value/255*100;
    //Serial.println(Q2);
}

void Q2off(){
    ledcWrite(Q2Channel,iwrite_min);
    //Q2 = iwrite_min/255*100;
    //Serial.println(Q2);
}

void ledon(){
    ledcWrite(ledChannel,iwrite_value);
}

void ledoff(){
    ledcWrite(ledChannel,iwrite_min);
}

void cektemp(){
  degC = analogRead(pinT1) * 0.322265625 ;    // use for 3.3v AREF
  cel = degC/10;
  degC1 = analogRead(pinT2) * 0.322265625 ;    // use for 3.3v AREF
  cel1 = degC1/10;

  Serial.print("Temperature: ");
  Serial.print(cel);   // print the temperature T1 in Celsius
  Serial.print("Â°C");
  Serial.print("  ~  "); // separator between Celsius and Fahrenheit
  Serial.print(cel1);   // print the temperature T2 in Celsius
  Serial.println("Â°C");
}

void receivedCallback(char* topic, byte* payload, unsigned int length) {

/* we got '1' -> Q1_on */
  if ((char)payload[0] == '1') {
        Q1on();
        Serial.println("Q1 On");
  } 
  
/* we got '2' -> Q1_off */
  if ((char)payload[0] == '2') {
        Q1off(); 
        Serial.println("Q1 Off");  
  } 

/* we got '3' -> Q2_on */
  if ((char)payload[0] == '3') {
        Q2on();
        Serial.println("Q2 On");
  } 
  
/* we got '4' -> Q2_off */
  if ((char)payload[0] == '4') {
        Q2off(); 
        Serial.println("Q2 Off");  
  } 
}

void loop() { 
  char suhu1[4];
  char suhu2[4];
  client.loop();

  // put your main code here, to run repeatedly:
  cektemp();
  if (cel > batas_suhu_atas){
    Q1off();
    ledon();
  }
  else {
    Q1on();
    ledoff();
  }
  if (cel1 > batas_suhu_atas){
    Q2off();
    ledon();
  }
  else {
    Q2on();
    ledoff();
  }
  delay (100);

 
  Serial.print("Temperature T1: ");
  Serial.print(cel);
  Serial.print(" Celcius ");
  Serial.println(" send to Broker MQTT");
 
  dtostrf(cel, 1, 0, suhu1);
  client.publish("Suhu1",suhu1);
  
  delay (200);

  Serial.print("Temperature T2: ");
  Serial.print(cel1);
  Serial.print(" Celcius ");
  Serial.println(" send to Broker MQTT");
 
  dtostrf(cel1, 1, 0, suhu2);
  client.publish("Suhu2",suhu2);

  delay (200);

}

Download Program Monitoring dan Kontrol Suhu On/Off via IoT Menggunakan Pengaturan PWM dalam Arduino (silahkan klik-kanan Save link as), di sini : 06-Suhu_IoT_On_Off2.ino.